PROPERTIES
TITANIUM PIN (Grade 5)SET
The ergonomic design of the applicator allows easy removal of the pin and easy
fixation of the membrane. The notch, which is approximately half the length of the
pin, ensures that the pin is pin engages bone easily.

Ergonomically designed for easy capture and quick application of titanium pins. The Pin Applicator offers single-handed fixation of resorbable and non-resorbable membranes.

The macro geometry of The macro geometry of Titanium Pins head allows
insertion without bone preparation whilst the head design prevents bending during
application. These features result in higher torque insertion, better primary stability,
and a more predictable success rate.

cannot occur.

• Ligamed Flexible Strip Implantation;
• Ligamed Flexible Strip can be applied to the
surgical area directly or combined with bone marrow
aspirate or blood.
• When the Ligamed Flexible Strip is wetted with
blood, its flexibility increases significantly.
• Ligamed Flexible Strip must be implanted just
before all metallic implants are stabilized and the
surgical site is closed.
• Ligamed Flexible Strip can be cut and placed in
the spinal cage.
• Ligamed Flexible Strip gains osteoinductive
characteristic due to silicate addition to the product
content.

SILICATE ADDITIVE GRANULE, STICK & BLOCK Safe, Biocompatible and Sterile Ligamed grafts are supplied sterile and is CE marked as a Class III Medical Device according to 93/42 / EC medical device directive. Biocompatibility tests (in vitro and in vivo), biodegradation tests, bioburden and sterility tests were applied to the products.

Radiopaque CT and X-ray traceability is possible. 100% Synthetic Does not contain human or animal tissue,therefore there is no risk of disease transmission. 0.25-9 mm.

Osteoconductive and Osteoinductive It supports new bone formation. It acts as a roof for the cells that enable new bone formation. It has a structure similar to the mineral found naturally in bone. The silicate additive increases the protein retention to the graft and gives it bioactive characteristics.

Ligamed products are designed to repair bone defects caused
by surgery or traumatic injury, increase bone formation or
support the formation of new bone tissue in non-load bearing
clinical applications. It can be mixed with bone marrow, blood
and other clinically known bone grafts.

Ligamed products are designed to repair bone defects caused
by surgery or traumatic injury, increase bone formation or
support the formation of new bone tissue in non-load bearing
clinical applications. It can be mixed with bone marrow, blood
and other clinically known bone grafts.

Ligamed products are designed to repair bone defects caused by surgery or traumatic injury, increase bone formation or support the formation of new bone tissue in non-load bearing clinical applications. It can be mixed with bone marrow, blood and other clinically known bone grafts.

SKU: m1a30
Category: MA
Multi-unit, 30° angled, height 1 mm,
material: Ti6Al4V.

Crestal Approach Sinus Kit
The most advanced safety and simple for all of sinus lift operation

The Component of Crestal Approach Sinus Kit:

Point Drill
Guide Drill
Aqua Tip - Elevation
Aqua Tip - Dual Action
Sinus R Drill
Silicon Tube
Silicone Tube
Bone Pusher/ Depth Gauge
Bone Carrier
Stopper
This kit will minimize the damages to the membrane during the operation.

Straight Cement Abutment A3
Material: Ti6Al4V
Gingiva height: 3 mm

ROOTT R is based on a two-piece dental implant with self-tapping thread for maximum prosthetic options for most common and necessary cases with all tools needed. Straight cement abutment allows reducing the time usually spent on milling standard abutments and securing the lock. Conical shape ensures quality and easy handling in precision.

Anodized gold colour for the comfort of the patient and aesthetics
Tight connection to the implant – preventing micromotions
Can be used for the cementless cementation process

Analog of multiunite. material : SS

ROOTT Dental Implant. compressive type. diameter 5.5 mm. length 12 mm. material Ti6Al4V

ROOTT C implant is a one-piece compressive type implant that is specially designed to provide perfect primary stability and is used in clinical situations when horizontal alveolar ridge atrophy is observed.

It can be used in combination with basal implants and allows flap and flapless placement.

It has a unique feature to be bent. This feature makes the prosthetic treatment easier.

The length of the neck is 3 mm.

Divergence or convergence up to 10˚ is possible between this type of implants because the slope of the abutment is 5˚.

If the divergence or convergence between this type of implants is found more than 5˚ then the abutment can be grinded.

The abutment is designed for cemented or conometric (telescopic) type of fixation as well.

Can be used with caution to create single restorations in situations where high primary stability is achieved on placement.

Bendable neck

Depending on the length of the implant the abutment can be bent up to 15 degrees, as long as the implant is placed with high primary stability.

ROOTT Dental Implant. compressive type. diameter 4.5 mm. length 14 mm. material Ti6Al4V

ROOTT C implant is a one-piece compressive type implant that is specially designed to provide perfect primary stability and is used in clinical situations when horizontal alveolar ridge atrophy is observed.

It can be used in combination with basal implants and allows flap and flapless placement.

It has a unique feature to be bent. This feature makes the prosthetic treatment easier.

The length of the neck is 3 mm.

Divergence or convergence up to 10˚ is possible between this type of implants because the slope of the abutment is 5˚.

If the divergence or convergence between this type of implants is found more than 5˚ then the abutment can be grinded.

The abutment is designed for cemented or conometric (telescopic) type of fixation as well.

Can be used with caution to create single restorations in situations where high primary stability is achieved on placement.

Bendable neck

Depending on the length of the implant the abutment can be bent up to 15 degrees, as long as the implant is placed with high primary stability.

This line is about a two-piece implant with an active thread for better osseointegration, ensuring perfect stability in the jaw and including a single internal connection, providing a wide range of prosthetic solutions. ROOTT R implant is a single platform with multiple possibilities, ensuring no micro gaps or micro movements. It’s about easy implant usage without compromising precision and comfort.

Suitable for single and multiple unit restorations with delayed and immediate implant placement in the upper and lower jaws in all types of bone tissue. The implant can be placed by a flap or flapless approach. The gold anodized neck is developed for cases of long-term usage when after gingiva lowering to mount on the abutment on top with no need to remove the implant. Implant placement is also possible immediately following a tooth extraction, as long as sufficient bone tissue is available vertically and horizontally.
The prosthetic platform (internal connection) is the same in all sizes of the implants.

Every implant comes with free multi-functional part CRE, which allows you to avoid additional part purchases, as it can be used as healing or temporary abutment, helping you in direct scan and transfer.

Two-piece implant with self-tapping thread:

Excellent primary stability
Free multi-functional part
Conical connection
Extra thin & strong
Each implant is delivered in a sterile package with a multifunctional carrier, a two-component holder, a cover screw, and labels for clinical records.

Content of each box:

Multifunction carrier with fixing screw
Sterile blister with ROOTT R implant
Labels for clinical records
Two-component holder
Cover screw

ROOTT R Dental Implant. root form type. diameter 3.0 mm. length 16 mm. material Ti6Al4V

Classical ROOT FORM or ,,V‘‘ (tapered shape design) form dental implant with active thread (to ensure perfect primary stability) and internal conus connection (platform switching).

Suitable for single and multiple unite restorations with delayed and immediate implant placement in the upper and lower jaws in all types of bone tissue.

The implant can be placed by flap or flapless approach. Implant placement is also possible immediately following tooth extraction, as long as sufficient bone tissue is available vertically and horizontally.

The prosthetic platform (internal connection) is the same in all sizes of the implants!

ROOTT R implant packaging

Each implant is delivered in a sterile package with a multifunctional carrier, a two-component holder, a cover screw and labels for clinical records.

Content of each box:

Sterile blister with ROOTT R implant
Multifunction carrier with fixing screw
Two-component holder
Cover screw
Labels for clinical records

ROOTT Dental Implant. compressive type. diameter 5.5 mm. length 10 mm. material Ti6Al4V

ROOTT C implant is a one-piece compressive type implant that is specially designed to provide perfect primary stability and is used in clinical situations when horizontal alveolar ridge atrophy is observed.

It can be used in combination with basal implants and allows flap and flapless placement.

It has a unique feature to be bent. This feature makes the prosthetic treatment easier.

The length of the neck is 3 mm.

Divergence or convergence up to 10˚ is possible between this type of implants because the slope of the abutment is 5˚.

If the divergence or convergence between this type of implants is found more than 5˚ then the abutment can be grinded.

The abutment is designed for cemented or conometric (telescopic) type of fixation as well.

Can be used with caution to create single restorations in situations where high primary stability is achieved on placement.

Bendable neck

Depending on the length of the implant the abutment can be bent up to 15 degrees, as long as the implant is placed with high primary stability.

ROOTT Dental Implant. compressive type. diameter 5.0 mm. length 10 mm. material Ti6Al4V

ROOTT C implant is a one-piece compressive type implant that is specially designed to provide perfect primary stability and is used in clinical situations when horizontal alveolar ridge atrophy is observed.

It can be used in combination with basal implants and allows flap and flapless placement.

It has a unique feature to be bent. This feature makes the prosthetic treatment easier.

The length of the neck is 3 mm.

Divergence or convergence up to 10˚ is possible between this type of implants because the slope of the abutment is 5˚.

If the divergence or convergence between this type of implants is found more than 5˚ then the abutment can be grinded.

The abutment is designed for cemented or conometric (telescopic) type of fixation as well.

Can be used with caution to create single restorations in situations where high primary stability is achieved on placement.

Bendable neck

Depending on the length of the implant the abutment can be bent up to 15 degrees, as long as the implant is placed with high primary stability.

SKU: spcoio
Categories: ROOTT R, Scan-post

SKU: abm
Category: With platform
Abutment burn out with metal hex
Material: POM-C, Ti6Al4V

ROOTT Dental Implant. compressive type. diameter 5.0 mm. length 12 mm. material Ti6Al4V

ROOTT C implant is a one-piece compressive type implant that is specially designed to provide perfect primary stability and is used in clinical situations when horizontal alveolar ridge atrophy is observed.

It can be used in combination with basal implants and allows flap and flapless placement.

It has a unique feature to be bent. This feature makes the prosthetic treatment easier.

The length of the neck is 3 mm.

Divergence or convergence up to 10˚ is possible between this type of implants because the slope of the abutment is 5˚.

If the divergence or convergence between this type of implants is found more than 5˚ then the abutment can be grinded.

The abutment is designed for cemented or conometric (telescopic) type of fixation as well.

Can be used with caution to create single restorations in situations where high primary stability is achieved on placement.

Bendable neck

Depending on the length of the implant the abutment can be bent up to 15 degrees, as long as the implant is placed with high primary stability.

ROOTT Dental Implant, compressive type, diameter 3.5 mm, length 16 mm, multiunite, material: Ti6Al4V.

ROOTT M implant with regular multi-unit type abutment is designed just for screw-retained prostheses;

It has a compression thread, just like the other Compressive implants.

Divergence or convergence up to 60˚ is possible between these types of implants because the slope of the abutment is 30˚.

Implant abutment is unique because it has 2,5mm ø fixation screw such dimensions of the screw gives big mechanical resistance comparing to regular 1.6-1.8mm ø fixation screw that can be found in other systems.

It can be used not only for full arc fixed dental prostheses.

The implant’s abutment is similar to M abutment or ROOTT P implant’s abutment.

It can be used in combination with ROOTT P, ROOTT S and ROOTT R implants with multi-unit abutments and allows flap and flapless placement.

Advantages of ROOTT M:

Simple placement
Rich variety of prosthetic solutions
Cement free
Immediate loading
Excellent primary stability in all types of bone
Resistant to higher loads in comparing with ROOTT S
ROOTT M implant packaging

Each implant is delivered in a sterile package with a multifunctional carrier, a two-component holder and labels for clinical records.

Content of each box:

Sterile blister with ROOTT M implant
Multifunction carrier with fixing screw
Two-component holder
Labels for clinical records

ROOTT Dental Implant, compressive type, diameter 4.0 mm, length 8 mm, multiunite, material: Ti6Al4V.

ROOTT M implant with regular multi-unit type abutment is designed just for screw-retained prostheses;

It has a compression thread, just like the other Compressive implants.

Divergence or convergence up to 60˚ is possible between these types of implants because the slope of the abutment is 30˚.

Implant abutment is unique because it has 2,5mm ø fixation screw such dimensions of the screw gives big mechanical resistance comparing to regular 1.6-1.8mm ø fixation screw that can be found in other systems.

It can be used not only for full arc fixed dental prostheses.

The implant’s abutment is similar to M abutment or ROOTT P implant’s abutment.

It can be used in combination with ROOTT P, ROOTT S and ROOTT R implants with multi-unit abutments and allows flap and flapless placement.

Advantages of ROOTT M:

Simple placement
Rich variety of prosthetic solutions
Cement free
Immediate loading
Excellent primary stability in all types of bone
Resistant to higher loads in comparing with ROOTT S
ROOTT M implant packaging

Each implant is delivered in a sterile package with a multifunctional carrier, a two-component holder and labels for clinical records.

Content of each box:

Sterile blister with ROOTT M implant
Multifunction carrier with fixing screw
Two-component holder
Labels for clinical records

ROOTT Dental Implant, compressive type, diameter 4.0 mm, length 14 mm, multiunite, material: Ti6Al4V.

ROOTT M implant with regular multi-unit type abutment is designed just for screw-retained prostheses;

It has a compression thread, just like the other Compressive implants.

Divergence or convergence up to 60˚ is possible between these types of implants because the slope of the abutment is 30˚.

Implant abutment is unique because it has 2,5mm ø fixation screw such dimensions of the screw gives big mechanical resistance comparing to regular 1.6-1.8mm ø fixation screw that can be found in other systems.

It can be used not only for full arc fixed dental prostheses.

The implant’s abutment is similar to M abutment or ROOTT P implant’s abutment.

It can be used in combination with ROOTT P, ROOTT S and ROOTT R implants with multi-unit abutments and allows flap and flapless placement.

Advantages of ROOTT M:

Simple placement
Rich variety of prosthetic solutions
Cement free
Immediate loading
Excellent primary stability in all types of bone
Resistant to higher loads in comparing with ROOTT S
ROOTT M implant packaging

Each implant is delivered in a sterile package with a multifunctional carrier, a two-component holder and labels for clinical records.

Content of each box:

Sterile blister with ROOTT M implant
Multifunction carrier with fixing screw
Two-component holder
Labels for clinical records

ROOTT Dental Implant, compressive type, diameter 3.5 mm, length 14 mm, multiunite, material: Ti6Al4V.

ROOTT M implant with regular multi-unit type abutment is designed just for screw-retained prostheses;

It has a compression thread, just like the other Compressive implants.

Divergence or convergence up to 60˚ is possible between these types of implants because the slope of the abutment is 30˚.

Implant abutment is unique because it has 2,5mm ø fixation screw such dimensions of the screw gives big mechanical resistance comparing to regular 1.6-1.8mm ø fixation screw that can be found in other systems.

It can be used not only for full arc fixed dental prostheses.

The implant’s abutment is similar to M abutment or ROOTT P implant’s abutment.

It can be used in combination with ROOTT P, ROOTT S and ROOTT R implants with multi-unit abutments and allows flap and flapless placement.

Advantages of ROOTT M:

Simple placement
Rich variety of prosthetic solutions
Cement free
Immediate loading
Excellent primary stability in all types of bone
Resistant to higher loads in comparing with ROOTT S
ROOTT M implant packaging

Each implant is delivered in a sterile package with a multifunctional carrier, a two-component holder and labels for clinical records.

Content of each box:

Sterile blister with ROOTT M implant
Multifunction carrier with fixing screw
Two-component holder
Labels for clinical records

ROOTT Dental Implant, compressive type, diameter 3.0 mm, length 14 mm, multiunite, material: Ti6Al4V.

ROOTT M implant with regular multi-unit type abutment is designed just for screw-retained prostheses;

It has a compression thread, just like the other Compressive implants.

Divergence or convergence up to 60˚ is possible between these types of implants because the slope of the abutment is 30˚.

Implant abutment is unique because it has 2,5mm ø fixation screw such dimensions of the screw gives big mechanical resistance comparing to regular 1.6-1.8mm ø fixation screw that can be found in other systems.

It can be used not only for full arc fixed dental prostheses.

The implant’s abutment is similar to M abutment or ROOTT P implant’s abutment.

It can be used in combination with ROOTT P, ROOTT S and ROOTT R implants with multi-unit abutments and allows flap and flapless placement.

Advantages of ROOTT M:

Simple placement
Rich variety of prosthetic solutions
Cement free
Immediate loading
Excellent primary stability in all types of bone
Resistant to higher loads in comparing with ROOTT S
ROOTT M implant packaging

Each implant is delivered in a sterile package with a multifunctional carrier, a two-component holder and labels for clinical records.

Content of each box:

Sterile blister with ROOTT M implant
Multifunction carrier with fixing screw
Two-component holder
Labels for clinical records

ROOTT Dental Implant, compressive type, diameter 5.0 mm, length 10 mm, multiunite, material: Ti6Al4V.

ROOTT M implant with regular multi-unit type abutment is designed just for screw-retained prostheses;

It has a compression thread, just like the other Compressive implants.

Divergence or convergence up to 60˚ is possible between these types of implants because the slope of the abutment is 30˚.

Implant abutment is unique because it has 2,5mm ø fixation screw such dimensions of the screw gives big mechanical resistance comparing to regular 1.6-1.8mm ø fixation screw that can be found in other systems.

It can be used not only for full arc fixed dental prostheses.

The implant’s abutment is similar to M abutment or ROOTT P implant’s abutment.

It can be used in combination with ROOTT P, ROOTT S and ROOTT R implants with multi-unit abutments and allows flap and flapless placement.

Advantages of ROOTT M:

Simple placement
Rich variety of prosthetic solutions
Cement free
Immediate loading
Excellent primary stability in all types of bone
Resistant to higher loads in comparing with ROOTT S
ROOTT M implant packaging

Each implant is delivered in a sterile package with a multifunctional carrier, a two-component holder and labels for clinical records.

Content of each box:

Sterile blister with ROOTT M implant
Multifunction carrier with fixing screw
Two-component holder
Labels for clinical records

ROOTT Dental Implant, compressive type, diameter 4.0 mm, length 12 mm, multiunite, material: Ti6Al4V.

ROOTT M implant with regular multi-unit type abutment is designed just for screw-retained prostheses;

It has a compression thread, just like the other Compressive implants.

Divergence or convergence up to 60˚ is possible between these types of implants because the slope of the abutment is 30˚.

Implant abutment is unique because it has 2,5mm ø fixation screw such dimensions of the screw gives big mechanical resistance comparing to regular 1.6-1.8mm ø fixation screw that can be found in other systems.

It can be used not only for full arc fixed dental prostheses.

The implant’s abutment is similar to M abutment or ROOTT P implant’s abutment.

It can be used in combination with ROOTT P, ROOTT S and ROOTT R implants with multi-unit abutments and allows flap and flapless placement.

Advantages of Compressive M:

Simple placement
Rich variety of prosthetic solutions
Cement free
Immediate loading
Excellent primary stability in all types of bone
Resistant to higher loads in comparing with Compressive MS
Compressive M implant packaging

Each implant is delivered in a sterile package with a multifunctional carrier, a two-component holder and labels for clinical records.

Content of each box:

Sterile blister with Compressive M implant
Multifunction carrier with fixing screw
Two-component holder
Labels for clinical records