ROOTT Dental Implant, compressive type, diameter 4.5 mm, length 16 mm, pterygoid, multi-unit, material: Ti6Al4V.

This is hybrid form unique designed dental implant. ROOTT P implant is created for implantation in to tuber maxillae with additional fixation in the processus pterygoideus of oss sphenoidalis, that has very strong cortical bone.

This type of implantation helps to avoid sinus lifting procedures.

This is an alternative treatment to zygoma implantation with much easier surgery and more comfortable to the patient prostheses design.

ROOTT P implant with regular multi-unit type abutment is designed just for screw retained prostheses.

Divergence or convergence up to 60˚ is possible between this type of implants because the slope of abutment is 30˚.

Implant abutment is also unique because it has 2,5mm ø fixation screw. Such dimensions of the screw gives big mechanical resistance comparing to regular 1.6-1.8mm ø fixation screw that can be found in other systems.

Can be used not only for full arc fixed dental prostheses.

The implant’s abutment is similar to M abutment or ROOTT M implant’s abutment.

Advantages of ROOTT P:

Simple placement
Rich variety of prosthetic solutions
Cement free
Immediate loading
Excellent primary stability in pterygoid area
Resistant to higher loads in comparing with ROOTT S
ROOTT P implant packaging

Each implant is delivered in a sterile package with a multifunctional carrier, a two-component holder and labels for clinical records.

Content of each box:

Sterile blister with ROOTT P implant
Multifunction carrier with fixing screw
Two-component holder
Labels for clinical records

ROOTT Dental Implant. compressive type. diameter 4.0 mm. length 6 mm. material Ti6Al4V

ROOTT C implant is a one-piece compressive type implant that is specially designed to provide perfect primary stability and is used in clinical situations when horizontal alveolar ridge atrophy is observed.

It can be used in combination with basal implants and allows flap and flapless placement.

It has a unique feature to be bent. This feature makes the prosthetic treatment easier.

The length of the neck is 3 mm.

Divergence or convergence up to 10˚ is possible between this type of implants because the slope of the abutment is 5˚.

If the divergence or convergence between this type of implants is found more than 5˚ then the abutment can be grinded.

The abutment is designed for cemented or conometric (telescopic) type of fixation as well.

Can be used with caution to create single restorations in situations where high primary stability is achieved on placement.

Bendable neck

Depending on the length of the implant the abutment can be bent up to 15 degrees, as long as the implant is placed with high primary stability.

MARATHON-Ki-20 Implant Motor (Fiber Optic)

Fiber Optic LED Control
Speed Range: 20~40.000 rpm
Torque Range: 5~70 Ncm
LCD Display

ROOTT Dental Implant. compressive type. diameter 3.5 mm. length 10 mm. material Ti6Al4V

ROOTT C implant is a one-piece compressive type implant that is specially designed to provide perfect primary stability and is used in clinical situations when horizontal alveolar ridge atrophy is observed.

It can be used in combination with basal implants and allows flap and flapless placement.

It has a unique feature to be bent. This feature makes the prosthetic treatment easier.

The length of the neck is 3 mm.

Divergence or convergence up to 10˚ is possible between this type of implants because the slope of the abutment is 5˚.

If the divergence or convergence between this type of implants is found more than 5˚ then the abutment can be grinded.

The abutment is designed for cemented or conometric (telescopic) type of fixation as well.

Can be used with caution to create single restorations in situations where high primary stability is achieved on placement.

Bendable neck

Depending on the length of the implant the abutment can be bent up to 15 degrees, as long as the implant is placed with high primary stability.

The sinus lifts surgical kit is a lightweight, well-balanced set of surgical instruments for sinus lift procedures. If back teeth are to get replaced after having been missing for a long time, the sinus cavity encompasses a tendency to become pneumatized or "bubble down. Implants won't find adequate bony support they have from the sinus floor. For successful implantation, considerably more bone is required. For making up this missing bone there's a typical procedure which will be done to make additional bone height and lead to an adequate receptive site to put a tooth implant and return the choice of getting attached permanent teeth again. Sinus lifting procedures as of today supporting different techniques, suiting the clinician's favorite/needed approach (Crestal or Lateral) and guaranteeing simple and intuitive surgical systems with maximal safety.

The Component:

Guide Drill (RPM 800-1000): Making the first hole to the point of perforation on the cortical bone before the main drilling
CrestaI Reamer (RPM 500-800): The Flatted end tip of the crestal reamer minimizes damage to the membrane.
Bone Carrier (Crestal): In the case of crestal approach sinus lift, inserting the bone graft inside of the maxillary sinus with the bone condenser.
Window Drill (RPM 800-1000): 1. When attempting the window perforation of the cartilage of the maxillary sinus, these make it easy to find centering of a bone hole made by the crestal reamer.


There are 0.5mm sequential differences (1 mm-3mm) that are able to make the window perforation easier.
Lateral Drill (RPM 200-1500): 1. Not in the case of using window drills, use creating window perforation easier and safer.


2 steps stopper provides more precision perforation to minimize damage to the membrane.
Side Cutter: Use this instrument, in case of the window cutting surface, is not flat or/and rugged.
Aqua Tip: To elevate the separated membrane from the maxillary bone, use to connect with silicone tube and syringe for injecting the saline solution.
Bone Carrier (Lateral): In the case of the lateral approach sinus lift, inserting the bone graft inside of the maxillary sinus with the bone condenser.
Bone Condenser/Depth Gauge: 1. Measure the elevated depth of the membrane through the band marking and using stoppers.


To push the bone graft to the inside of the maxillary sinus.
Stopper: 1. Connecting with a drill to drill to the same length of the cartilage height of maxillary sinus which is measured by CT


Connecting with the depth gauge to measure the depth of the elevated membrane


Feature of Total Sinus Kit:

-The most advanced, safe and simple way for all sinus lift techniques
Open and closed techniques
Excellent in safety, simple operation, and visual convenience

The sinus lifts surgical kit is a lightweight, well-balanced set of surgical instruments for sinus lift procedures. If back teeth are to get replaced after having been missing for a long time, the sinus cavity encompasses a tendency to become pneumatized or "bubble down. Implants won't find adequate bony support they have from the sinus floor. For successful implantation, considerably more bone is required. For making up this missing bone there's a typical procedure which will be done to make additional bone height and lead to an adequate receptive site to put a tooth implant and return the choice of getting attached permanent teeth again. Sinus lifting procedures as of today supporting different techniques, suiting the clinician's favorite/needed approach (Crestal or Lateral) and guaranteeing simple and intuitive surgical systems with maximal safety.

The Component:

Guide Drill (RPM 800-1000): Making the first hole to the point of perforation on the cortical bone before the main drilling
CrestaI Reamer (RPM 500-800): The Flatted end tip of the crestal reamer minimizes damage to the membrane.
Bone Carrier (Crestal): In the case of crestal approach sinus lift, inserting the bone graft inside of the maxillary sinus with the bone condenser.
Window Drill (RPM 800-1000): 1. When attempting the window perforation of the cartilage of the maxillary sinus, these make it easy to find centering of a bone hole made by the crestal reamer.


There are 0.5mm sequential differences (1 mm-3mm) that are able to make the window perforation easier.
Lateral Drill (RPM 200-1500): 1. Not in the case of using window drills, use creating window perforation easier and safer.


2 steps stopper provides more precision perforation to minimize damage to the membrane.
Side Cutter: Use this instrument, in case of the window cutting surface, is not flat or/and rugged.
Aqua Tip: To elevate the separated membrane from the maxillary bone, use to connect with silicone tube and syringe for injecting the saline solution.
Bone Carrier (Lateral): In the case of the lateral approach sinus lift, inserting the bone graft inside of the maxillary sinus with the bone condenser.
Bone Condenser/Depth Gauge: 1. Measure the elevated depth of the membrane through the band marking and using stoppers.


To push the bone graft to the inside of the maxillary sinus.
Stopper: 1. Connecting with a drill to drill to the same length of the cartilage height of maxillary sinus which is measured by CT


Connecting with the depth gauge to measure the depth of the elevated membrane


Feature of Total Sinus Kit:

-The most advanced, safe and simple way for all sinus lift techniques
Open and closed techniques
Excellent in safety, simple operation, and visual convenience

The life of the screw remove drill, the screw remove the tap and all of the fixture removals is dramatically improved to 10 times longer the special hard material (Tungsten Carbide)



Detail View

The Components:

Screw Remove Drill (PRM 800-1000): This is the tool to take out the broken screw by Turning it in a reverse way.
Screw Remove Guide: Instruments to guarantee the screw remove drill can be stable working in the center of the broken screw.
Screw Remove Tap (PRM 30-80): This is the tool to take out the broken screw by turning it in a reverse way.
Fixture Remove: To take out useless fixtures by bone loss or broken, use this by locking in a reverse way.
Screw Remove Bar: This tool is for t taking out broken screw through picking up.
Cover Screw Remove: This is the tool after making the hole-like slot shape and tum in a reverse way to take out.
Adapter: Use this attachment with the Fixture Remove and the Cover Screw Remove for when you put your fingers to screw.


Feature of Total Remove Kit:

The life of the screw remove drill, the screw removes the tap and all of the fixture removals is dramatically improved to 10 times longer by using the special hard material (Tungsten Carbide).



The direction of Use:

In a case that there is a broken screw in the fixture

Check the screw inside of the fixture.
Use the screw remove guide (HEG27H/HIG160/HSG22H/HSG22N) according to the fixture kind.
Use the screw remove drill (HSD 1032} on the reverse side with high speed.
Put this screw remove the top (HST1025) and use in reverse side to take the broken screw out slowly.


In a case of a useless cover screw:

Make a flat driver groove to the cover screw by using a saw cutter.
Take out the cover screw by using the cover screw remove (HSD054S/HS00542) through counterclockwise rotation.


In a case that there is a useless fixture

Choose the proper type of fixture to remove drills (HRF22/HRF16/HRF16N) according to the type and size of fixture which is fractured or damaged.
Insert the fixture remove drill chosen connecting with the adapter (HSH40) into the hole of the fixture and lock each other through counterclockwise movement.
Attach the ratchet wrench (HRW9785) to the fixture remove the drill and start to screw off very carefully through counter-clockwise rotation.
Once it starts moving, accordingly take the fixture out by using counter-clockwise rotation

ROOTT Dental Implant, compressive type, diameter 3.5 mm, length 18 mm, multiunit, material: Ti6Al4V.

ROOTT M implant with regular multi-unit type abutment is designed just for screw-retained prostheses;

It has a compression thread, just like the other Compressive implants.

Divergence or convergence up to 60˚ is possible between these types of implants because the slope of the abutment is 30˚.

Implant abutment is unique because it has 2,5mm ø fixation screw such dimensions of the screw gives big mechanical resistance comparing to regular 1.6-1.8mm ø fixation screw that can be found in other systems.

It can be used not only for full arc fixed dental prostheses.

The implant’s abutment is similar to M abutment or ROOTT P implant’s abutment.

It can be used in combination with ROOTT P, ROOTT S and ROOTT R implants with multi-unit abutments and allows flap and flapless placement.

Advantages of ROOTT M:

Simple placement
Rich variety of prosthetic solutions
Cement free
Immediate loading
Excellent primary stability in all types of bone
Resistant to higher loads in comparing with ROOTT S
ROOTT M implant packaging

Each implant is delivered in a sterile package with a multifunctional carrier, a two-component holder and labels for clinical records.

Content of each box:

Sterile blister with ROOTT M implant
Multifunction carrier with fixing screw
Two-component holder
Labels for clinical records

ROOTT Dental Implant. compressive type. diameter 3.5 mm. length 8 mm.

ROOTT C implant is a one-piece compressive type implant that is specially designed to provide perfect primary stability and is used in clinical situations when horizontal alveolar ridge atrophy is observed.

It can be used in combination with basal implants and allows flap and flapless placement.

It has a unique feature to be bent. This feature makes the prosthetic treatment easier.

The length of the neck is 3 mm.

Divergence or convergence up to 10˚ is possible between this type of implants because the slope of the abutment is 5˚.

If the divergence or convergence between this type of implants is found more than 5˚ then the abutment can be grinded.

The abutment is designed for cemented or conometric (telescopic) type of fixation as well.

Can be used with caution to create single restorations in situations where high primary stability is achieved on placement.

Bendable neck

Depending on the length of the implant the abutment can be bent up to 15 degrees, as long as the implant is placed with high primary stability.

SKU: gf4
Category: Regular
Regular Healing abutment GF4
H (bone level): 5.8 mm
Gingiva height: 4 mm
Material: Ti6Al4V

ROOTT R is based on a two-piece dental implant with self-tapping thread for maximum prosthetic options for most common and necessary cases with all tools needed. ROOTT R healing abutment can help promote soft and hard tissue healing and protect from plaque and debris. Safe to remove and perfect fit of gingiva colour – all for the comfort of the patient.

Visually pleasing colour for simple identification and conceal
Wide variety of sizes in both GF and screw
Precise shape for less tension
Added holes for dental probe
Easily removed with SR tool

Straight Cement Abutment A4
Material: Ti6Al4V
Gingiva height: 4 mm

ROOTT R is based on a two-piece dental implant with self-tapping thread for maximum prosthetic options for most common and necessary cases with all tools needed. Straight cement abutment allows reducing the time usually spent on milling standard abutments and securing the lock. Conical shape ensures quality and easy handling in precision.

Anodized gold colour for the comfort of the patient and aesthetics
Tight connection to the implant – preventing micromotions
Can be used for the cementless cementation process

Provides Solid Performance For Surgical & Implant Procedures.

Designed Specifically For Oral & Implant Surgery, Surgic AP Delivers The Power And Performance For These Procedures.

201 Watt Power & 50 Ncm Torque, Together With A Wide Speed Range Of 200 - 40,000 RPM Offers The Flexibility And Fast Response Required For A Variety Of Surgical Procedures.

The Compact Console Is User-Friendly, Simple To Operate And Has Been Specifically Designed For The Aseptic Theater Environment.

Hypro-Sorb F® Membrane
Hypro-Sorb® F is a rigid, bilayer membrane made of 99.9% pure, crystalline Atelo-Collagen Type I, which is derived from the bovine Achilles tendon. Hypro-Sorb® F is 0.2 mm thick with high tensile and bending strength due to densely packed collagen fibers. Therefore, it is recommended to soak the membrane with saline or the patient’s blood for at least 1 minute before application to facilitate handling.

The resorption process occurs in two phases. During the first six to eight weeks,
Hypro-Sorb® F stays intact. The resorption of the membrane starts afterwards. The membrane is completely resorbed within six months.

PROPERTIES AND ADVANTAGES
0.2 mm rigid, bilayer membrane

pure, crystalline Atelo-Collagen Type I, free of immunogenic telopeptides

highest degree of tissue biocompatibility

highest safety with excellent wound healing characteristics

quick adaptation to the defect due to it is potent hydrophilic properties

reduced risk of dehiscence formation due to the texture and mild bacteriostatic effect of Atelo-Collagen

long barrier function of circa 16 weeks, complete resorption after 6 months

rough and smooth sides are clearly distinguishable

sterile and safe for five years after production

SKU: itm
Categories: Implant drivers M, Implant drivers M
Direct insertion tool

One Drilling System Kit

One Drilling System Kit has an innovative design and optimizes the surgical stage. With cylindrical shape, they have active tips with high cutting efficiency and excellent stability. Its parallel body contains straight flutes that help in irrigation and bone tissue collection.

The Components:

One Drill (RPM 800-1000): The drill is made ergonomically and provides not only safe drilling but also the size of implant you would like in one drilling instead of drilling many times.


The benefit of one drill:

Able to make the implant size in one drilling.
No bone heat.
Able to collect self-bone.
Big save of the surgery time.
Guide Drill (RPM 800-1000): The first drill you have to use and very good for setting up the implant position.


Opener OUT: Tools to disjoint the one drill as a shank part and a flute part.


Bone Remove/Depth Gauge (RPM 300-700): After the drilling, check the depth and remove the leftover bone.


Bone Pusher: Can take out the bone inside of the drill.


Pincette: Tool to remove remaining bone after using the one drill.


Stopper: 9 kinds of depth you can have.


Feature of One Drilling System Kit:

Increase the satisfaction of implant surgery by reducing the pain by minimizing the flap open with this system.
Done by one drilling for one implant system.
Easy to get the path, no bone heat.
Able to collect self-generated bone


The direction of Use:

Use the guide drill (GD3248) to be careful on the slippery strong bone surface after minimized flap opening.
Use the one drill of the same size drill according to the implant size you would like to place.
Check the depth with the bone remover (BR2116). If the depth is not deep enough, use the bone remover to remove the leftover bone with a stopper.
In case of when you find out a very hard bone (Dl or 02 bone), you may use one size bigger drill and put it in half only after using the same size drill of the implant size. In case of when you find out very soft bone, you may use one size smaller drill than the implant size.

Double A Guide Kit
Accurate Allocation

The Components of Double a Guide Kit:

Accurate Guide
Guide Drill
Accurate Pin
Tissue Punch
Boner Trimmer
Double A Guide Kit in UAE
An easy kit to irrigation for drilling.

Crestal Approach Sinus Kit
The most advanced safety and simple for all of sinus lift operation

The Component of Crestal Approach Sinus Kit:

Point Drill
Guide Drill
Aqua Tip - Elevation
Aqua Tip - Dual Action
Sinus R Drill
Silicon Tube
Silicone Tube
Bone Pusher/ Depth Gauge
Bone Carrier
Stopper
This kit will minimize the damages to the membrane during the operation.

ROOTT Dental Implant, basal ss type, diameter 3.5 mm, length 14 mm, material: Ti6Al4V.

ROOTT BS dental implant is a sandblasted version of the ROOTT B one-piece implant with a prolonged 1.5-7mm neck. Recommended in clinical situations when high (until 7mm) horizontally atrophied alveolar ridge is observed.

It has a unique feature to be bent. This feature makes the prosthetic treatment easier.

Implants with necks less than 3mm are not bendable.

Divergence or convergence up to 10˚ is possible between these types of implants because the slope of the abutment is 5˚.

If the divergence or convergence of more than 5˚ between these types of implants is found the abutment can be grinded.

The abutment is designed for cemented or conometric (telescopic) type of fixation as well.

The structural characteristics allow placement in bone that is deficient in height and width. They can be placed with flap or flapless technique.

ROOTT BS can be used to bypass the mandibular nerve and for the engagement of the cortical bone at the fusion of the pterygoid with the maxilla. Can be used in combination with Compressive implants.

Can be bent up to 15° after implant placement

Advantages:

Ideal for resorbed ridges
Immediate loading
Placement in a socket of an extracted tooth
Excellent protection from inflammation around the dental implant
Adjustment of abutment angle 15 degrees
Sandblasted

This line is about a two-piece implant with an active thread for better osseointegration, ensuring perfect stability in the jaw and including a single internal connection, providing a wide range of prosthetic solutions. ROOTT R implant is a single platform with multiple possibilities, ensuring no micro gaps or micro movements. It’s about easy implant usage without compromising precision and comfort.

Suitable for single and multiple unit restorations with delayed and immediate implant placement in the upper and lower jaws in all types of bone tissue. The implant can be placed by a flap or flapless approach. The gold anodized neck is developed for cases of long-term usage when after gingiva lowering to mount on the abutment on top with no need to remove the implant. Implant placement is also possible immediately following a tooth extraction, as long as sufficient bone tissue is available vertically and horizontally.
The prosthetic platform (internal connection) is the same in all sizes of the implants.

Every implant comes with free multi-functional part CRE, which allows you to avoid additional part purchases, as it can be used as healing or temporary abutment, helping you in direct scan and transfer.

Two-piece implant with self-tapping thread:

Excellent primary stability
Free multi-functional part
Conical connection
Extra thin & strong
Each implant is delivered in a sterile package with a multifunctional carrier, a two-component holder, a cover screw, and labels for clinical records.

Content of each box:

Multifunction carrier with fixing screw
Sterile blister with ROOTT R implant
Labels for clinical records
Two-component holder
Cover screw

This line is about a two-piece implant with an active thread for better osseointegration, ensuring perfect stability in the jaw and including a single internal connection, providing a wide range of prosthetic solutions. ROOTT R implant is a single platform with multiple possibilities, ensuring no micro gaps or micro movements. It’s about easy implant usage without compromising precision and comfort.

Suitable for single and multiple unit restorations with delayed and immediate implant placement in the upper and lower jaws in all types of bone tissue. The implant can be placed by a flap or flapless approach. The gold anodized neck is developed for cases of long-term usage when after gingiva lowering to mount on the abutment on top with no need to remove the implant. Implant placement is also possible immediately following a tooth extraction, as long as sufficient bone tissue is available vertically and horizontally.
The prosthetic platform (internal connection) is the same in all sizes of the implants.

Every implant comes with free multi-functional part CRE, which allows you to avoid additional part purchases, as it can be used as healing or temporary abutment, helping you in direct scan and transfer.

Two-piece implant with self-tapping thread:

Excellent primary stability
Free multi-functional part
Conical connection
Extra thin & strong
Each implant is delivered in a sterile package with a multifunctional carrier, a two-component holder, a cover screw, and labels for clinical records.

Content of each box:

Multifunction carrier with fixing screw
Sterile blister with ROOTT R implant
Labels for clinical records
Two-component holder
Cover screw

ROOTT Dental Implant. compressive type. diameter 3.0 mm. length 14 mm. material Ti6Al4V

ROOTT C implant is a one-piece compressive type implant that is specially designed to provide perfect primary stability and is used in clinical situations when horizontal alveolar ridge atrophy is observed.

It can be used in combination with basal implants and allows flap and flapless placement.

It has a unique feature to be bent. This feature makes the prosthetic treatment easier.

The length of the neck is 3 mm.

Divergence or convergence up to 10˚ is possible between this type of implants because the slope of the abutment is 5˚.

If the divergence or convergence between this type of implants is found more than 5˚ then the abutment can be grinded.

The abutment is designed for cemented or conometric (telescopic) type of fixation as well.

Can be used with caution to create single restorations in situations where high primary stability is achieved on placement.

Bendable neck

Depending on the length of the implant the abutment can be bent up to 15 degrees, as long as the implant is placed with high primary stability.

ROOTT Dental Implant. compressive type. diameter 4.5 mm. length 12 mm. material Ti6Al4V

ROOTT C implant is a one-piece compressive type implant that is specially designed to provide perfect primary stability and is used in clinical situations when horizontal alveolar ridge atrophy is observed.

It can be used in combination with basal implants and allows flap and flapless placement.

It has a unique feature to be bent. This feature makes the prosthetic treatment easier.

The length of the neck is 3 mm.

Divergence or convergence up to 10˚ is possible between this type of implants because the slope of the abutment is 5˚.

If the divergence or convergence between this type of implants is found more than 5˚ then the abutment can be grinded.

The abutment is designed for cemented or conometric (telescopic) type of fixation as well.

Can be used with caution to create single restorations in situations where high primary stability is achieved on placement.

Bendable neck

Depending on the length of the implant the abutment can be bent up to 15 degrees, as long as the implant is placed with high primary stability.

Hypro-Sorb® F membrane
Hypro-Sorb® F is a rigid, two-layer membrane made from 99.9% pure, crystalline atelo-collagen type I, which is obtained from the bovine Achilles tendon. Hypro-Sorb® F is 0.2 mm thick and has particularly high tensile and flexural strength due to densely packed collagen fibers. Therefore, for ease of use, we recommend soaking the membrane in saline or blood for at least 1 minute prior to use.

Membrane absorption occurs in two phases. Stays during the first six to eight weeks

Hypro-Sorb® F completely intact. The degradation process only begins after this time. The membrane is completely resorbed after six months.

FEATURES AND BENEFITS
0.2 mm rigid, two-layer membrane

pure, crystalline atelo-collagen type I, free from antigenic telopeptides

highest level of tissue biocompatibility

highest safety with excellent wound healing properties

rapid adaptation to the wound due to strong hydrophilic properties

reduced risk of dehiscence formation due to the stable consistency and bacteriostatic effect of atelo-collagen

long barrier function of around 16 weeks, complete resorption after 6 months

rough and smooth side of the membrane are clearly distinguishable

sterile and safe for five years from the date of manufacture

Total HaeNaem Bur Kit is used for cutting hard tissues - tooth or bone. Total HaeNaem Burs are made of steel, stainless steel, tungsten carbide and diamond grit.

There can be a bewildering range of dental burs in any dental catalogue, but for basic veterinary use only a few burs are needed.

These kits often come in a custom bur block and the burs included are often selected by a noted clinician.

When drilling with the world-patented bone densification drill “Haenambur”, no bone loss or overflow occurs.

POINT VIEW:

Maxillary Sinus Autografting is secure only by Drilling
Improves bone density from D4 to D2 which is weak due to drilling
Excellent Ridge expansion effect only by drilling
Maximize the benefits of the procedure with two special drills, the Maxillary Sinus lifting drill and the bone extension drill
Safe surgical operation due to the forward direction drilling like the existing drill direction is possible


The components:

Pilot Drill (RPM 800-1000): Making first hole to the point of perforation before using osseodensif ication burs
Expander 20 Drill (RPM800~1000)
Osseodensification Bur (RPM 800-10001): By using clockwise direction, perform general drilling in a bouncing-pumping motion with copious irrigation
SINUS 10 Drill (RPM800~1000)


Clinical Advantages:

Easy & Safety maxillary sinus autografting
Early fixture fixation on general implant placement
Enhance bone density for poor bone quality through bone condensing
Pain I Swelling I Recovery Period Reduction


Direction of Use:

1. By using the pilot drill, make first hole with a residual thickness of approx imatelylmm from the sinus floor (RPM 800-1000)

2. Depending upon the implant type and diameter, begin with the narrowest osseodensification bur (001824) with repeatedly bounding­ pumping motion

(RPM 800-1000)

3. As the next osseodens ification bur in the osteotomy, bone will be pushed toward the apical end and will begin to gent ly lift the membrane and autograft compacted bone.

4. Use the sequential osseodens ification burs with repeatedly bouncing-pumping motion to achieve maximum membrane lift of 3mm and reach f inal desired width for implant placement



Based on the experience and technology of manufacturing products of domestic implant companies leading the global market, The Haenaem bur kit is a kit that can be done with osseodensification, bone width expansion, maxillary sinus autogenous bone elevation.

The characteristics of the use of the haenaem bur Kit are that the bone expansion and maxillary sinus lift bur are separated for use to maximize the advantage, and the conventional driller who is familiar with forward drilling does not need to change the implant engine setting and eliminates mistake caused by the rotation direction.

Summarize the advantages of the haenaem Bur Kit :

First, it is possible to increase the Bone quality by the osseodensification , even if the bone quality is not good, it can accelerate the loading time. Second, it is possible to perform safe surgery by reducing pain after small swelling surgery with autologous bone graft through Crystal Approach. Third, it is possible to expand the bone safely by using a drill specialized in the narrow width of the mandible.

Fourth, in many cases where extraction and healing are insufficient, drilling alone can obtain a problem, so that fixing can be safely obtained when planted in septum.

ROOTT Dental Implant. compressive type. diameter 5.0 mm. length 6 mm. material Ti6Al4V

ROOTT C implant is a one-piece compressive type implant that is specially designed to provide perfect primary stability and is used in clinical situations when horizontal alveolar ridge atrophy is observed.

It can be used in combination with basal implants and allows flap and flapless placement.

It has a unique feature to be bent. This feature makes the prosthetic treatment easier.

The length of the neck is 3 mm.

Divergence or convergence up to 10˚ is possible between this type of implants because the slope of the abutment is 5˚.

If the divergence or convergence between this type of implants is found more than 5˚ then the abutment can be grinded.

The abutment is designed for cemented or conometric (telescopic) type of fixation as well.

Can be used with caution to create single restorations in situations where high primary stability is achieved on placement.

Bendable neck

Depending on the length of the implant the abutment can be bent up to 15 degrees, as long as the implant is placed with high primary stability.

This line is about a two-piece implant with an active thread for better osseointegration, ensuring perfect stability in the jaw and including a single internal connection, providing a wide range of prosthetic solutions. ROOTT R implant is a single platform with multiple possibilities, ensuring no micro gaps or micro movements. It’s about easy implant usage without compromising precision and comfort.

Suitable for single and multiple unit restorations with delayed and immediate implant placement in the upper and lower jaws in all types of bone tissue. The implant can be placed by a flap or flapless approach. The gold anodized neck is developed for cases of long-term usage when after gingiva lowering to mount on the abutment on top with no need to remove the implant. Implant placement is also possible immediately following a tooth extraction, as long as sufficient bone tissue is available vertically and horizontally.
The prosthetic platform (internal connection) is the same in all sizes of the implants.

Every implant comes with free multi-functional part CRE, which allows you to avoid additional part purchases, as it can be used as healing or temporary abutment, helping you in direct scan and transfer.

Two-piece implant with self-tapping thread:

Excellent primary stability
Free multi-functional part
Conical connection
Extra thin & strong
Each implant is delivered in a sterile package with a multifunctional carrier, a two-component holder, a cover screw, and labels for clinical records.

Content of each box:

Multifunction carrier with fixing screw
Sterile blister with ROOTT R implant
Labels for clinical records
Two-component holder
Cover screw

Perfect handling
No mixing – use directly from the syringe.
Ergonomic syringe for direct application through the osteotomy or small sinus window.
Easily moulded to match defect morphology.
Resilience to wash-away – even in a wet field.
No membrane
Perfect stability and resilience to micromovement – ideal for minimal access approaches with site-specific flap.
Premium Performance
‘significantly enhanced bone regeneration compared to β-TCP.’ (3,4)
‘radiographically, and histologically equivalence to autograft. (7)
Powerbone Putty resorbs completely in line with bone healing making it perfect for:
Socket grafting.
3 walled GBR defects.
Sinus Lift.
Bony Cysts.

TITANIUM PIN (Grade 5)SET

The ergonomic design of the applicator allows easy removal of the pin and easy
fixation of the membrane.The notch, which is approximately half the length of the
pin, ensures that the pin is pin engages bone easily.
Ergonomically designed for easy capture and quick application of titanium pins. The Pin Applicator offers single-handed fixation of resorbable and non-resorbable membranes.

The macro geometry of The macro geometry of Titanium Pins head allows
insertion without bone preparation whilst the head design prevents bending during
application. These features result in higher torque insertion, better primary stability,
and a more predictable success rate.
Distortion of the pin apex during handling
cannot occur.